ResMed AirFit P10 Nasal Pillow Mask

RRP: AU$289.00 OUR PRICE: AU$192.00

Stock: In Stock

Add a spare Mask Cushion to your mask order for a discounted price. Simply select a size from below and receive an extra cushion, to use as a backup or replacement.

Add a spare P10 Standard Fabric Headgear to your mask order to use as a backup or replacement.

Add 2x Unscented Mask Wipes for only $23 (RRP $33)

CURRENT OFFERS: 

  

FOR A LIMITED TIME, GET 30 DAYS MONEY BACK GUARANTEE ON SELECT RESMED PRODUCTS

We're determined to help you sleep well. If you're not completely satisfied, talk to our team to find your perfect match, or you can return your purchase within 30 days of the purchase for a full refund or exchange*. It's peace of mind you take home for a better night's sleep.
*Terms and Conditions apply.

Promotion Valid from 1 May to 31 December 2020.

*Full refund only applies to the selected ResMed products listed in the T&Cs, additional cushions/headgear/mask wipes not included in offer


ResMed’s lightweight AirFit P10 is a quiet achiever. It offers you comfort and reliability at barely a whisper, thanks to its innovative QuietAir™ woven mesh vent. This ultra-quiet vent provides advanced air diffusion that significantly reduces disturbance, by gently directing air away from both you and your bed partner. The Airfit P10 is comes equipped with three sizes of pillow - S, M and L.

PLEASE NOTE:  

Please Note: The Airfit P10 is designed to work with standard full size CPAP devices. The P10 maybe used with the ResMed Airmini travel device but requires a special connector designed to fit with the tubing on the Airmini. A link to the P10 airmini connector as well as the complete P10 Airmini setup pack can be found below in the related products section.


Authenticity guarantee: All of our ResMed products are sourced directly from ResMed Australia. 



ASSEMBLY

  1. Thread each arm of the frame through the fabric openings in the headgear so that the grey side faces out and coloured side faces in.
  2. Ensure the headgear is secured by pulling the fabric over the bottom edge of each headgear node.
  3. Insert the pillows into the P10 frame by pressing it in until the top and bottom clips click together.
  4. If humidification is used, simply place the HumidX or HumidX Plus into the vent module.
  5. Connect the AirMini tubing to the vent module by pushing their ends together and turn until they click into place.
  6. Lastly, connect the air tube by twisting it into the bottom of the vent module.

Everyday Cleaning

  1. Take the P10 apart into its main component parts, namely the nasal pillows, frame and P10 tube.
  2. Remove the HumidX before proceeding with cleaning.
  3. Gently rub each part in warm water (~30°C or 86°F) and mild liquid detergent until clean, with attention paid to the pillows and its small openings.
  4. Rinse well under running water and allow to air dry out of direct sunlight.

Weekly Cleaning

  1. Take the P10 apart into its main components parts, namely the frame, P10 tube and the fabric headgear.
  2. Remove the HumidX before proceeding with cleaning.
  3. Gently scrub the frame and its elbow area in warm water (~30°C or 86°F) and mild liquid detergent with a soft bristle brush.
  4. Rub and squeeze the headgear in warm water (~30°C or 86°F) and mild liquid detergent until clean.
  5. Rinse both the headgear and frame under running water until the water is clear. Ensure you also squeeze the headgear while rinsing.
  6. Allow both to air dry out of direct sunlight.

Managing Leaks

  1. While therapy is running, place your fingers around the upper and lower areas, where the P10 seals to the face, to check if air is escaping.
  2. If there are leaks, try adjusting the headgear to help with P10 fit. Simply spread them apart to loosen and draw them together to tighten.
  3. You can also readjust the pillows by pulling briefly on the P10 away from your nose to reseat them.
  4. Once the P10 is secure and comfortable, you’re ready to start therapy.

Note: When the device is running, a light breeze should be felt at the base of the vent module, but there should be no other areas of air leak. If leak occurs or continues, try refitting the cushion into the frame.